| CVE-2025-38040 | In the Linux kernel, the following vulnerability has been resolved: serial: mctrl_gpio: split disable_ms into sync and no_sync APIs The following splat has been observed on a SAMA5D27 platform using atmel_serial: BUG: sleeping function called from invalid context at kernel/irq/manage.c:738 in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0 preempt_count: 1, expected: 0 INFO: lockdep is turned off. irq event stamp: 0 hardirqs last enabled at (0): [<00000000>] 0x0 hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec softirqs last disabled at (0): [<00000000>] 0x0 CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74 Hardware name: Atmel SAMA5 Workqueue: hci0 hci_power_on [bluetooth] Call trace: unwind_backtrace from show_stack+0x18/0x1c show_stack from dump_stack_lvl+0x44/0x70 dump_stack_lvl from __might_resched+0x38c/0x598 __might_resched from disable_irq+0x1c/0x48 disable_irq from mctrl_gpio_disable_ms+0x74/0xc0 mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4 atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8 atmel_set_termios from uart_change_line_settings+0x15c/0x994 uart_change_line_settings from uart_set_termios+0x2b0/0x668 uart_set_termios from tty_set_termios+0x600/0x8ec tty_set_termios from ttyport_set_flow_control+0x188/0x1e0 ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc] wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth] hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth] hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth] hci_power_on [bluetooth] from process_one_work+0x998/0x1a38 process_one_work from worker_thread+0x6e0/0xfb4 worker_thread from kthread+0x3d4/0x484 kthread from ret_from_fork+0x14/0x28 This warning is emitted when trying to toggle, at the highest level, some flow control (with serdev_device_set_flow_control) in a device driver. At the lowest level, the atmel_serial driver is using serial_mctrl_gpio lib to enable/disable the corresponding IRQs accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to disable_irq (called in mctrl_gpio_disable_ms) being possibly called in some atomic context (some tty drivers perform modem lines configuration in regions protected by port lock). Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one and a blocking one. Replace mctrl_gpio_disable_ms calls with the relevant version depending on whether the call is protected by some port lock. | medium |
| CVE-2025-38039 | In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Avoid WARN_ON when configuring MQPRIO with HTB offload enabled When attempting to enable MQPRIO while HTB offload is already configured, the driver currently returns `-EINVAL` and triggers a `WARN_ON`, leading to an unnecessary call trace. Update the code to handle this case more gracefully by returning `-EOPNOTSUPP` instead, while also providing a helpful user message. | medium |
| CVE-2025-38038 | In the Linux kernel, the following vulnerability has been resolved: cpufreq: amd-pstate: Remove unnecessary driver_lock in set_boost set_boost is a per-policy function call, hence a driver wide lock is unnecessary. Also this mutex_acquire can collide with the mutex_acquire from the mode-switch path in status_store(), which can lead to a deadlock. So, remove it. | medium |
| CVE-2025-38037 | In the Linux kernel, the following vulnerability has been resolved: vxlan: Annotate FDB data races The 'used' and 'updated' fields in the FDB entry structure can be accessed concurrently by multiple threads, leading to reports such as [1]. Can be reproduced using [2]. Suppress these reports by annotating these accesses using READ_ONCE() / WRITE_ONCE(). [1] BUG: KCSAN: data-race in vxlan_xmit / vxlan_xmit write to 0xffff942604d263a8 of 8 bytes by task 286 on cpu 0: vxlan_xmit+0xb29/0x2380 dev_hard_start_xmit+0x84/0x2f0 __dev_queue_xmit+0x45a/0x1650 packet_xmit+0x100/0x150 packet_sendmsg+0x2114/0x2ac0 __sys_sendto+0x318/0x330 __x64_sys_sendto+0x76/0x90 x64_sys_call+0x14e8/0x1c00 do_syscall_64+0x9e/0x1a0 entry_SYSCALL_64_after_hwframe+0x77/0x7f read to 0xffff942604d263a8 of 8 bytes by task 287 on cpu 2: vxlan_xmit+0xadf/0x2380 dev_hard_start_xmit+0x84/0x2f0 __dev_queue_xmit+0x45a/0x1650 packet_xmit+0x100/0x150 packet_sendmsg+0x2114/0x2ac0 __sys_sendto+0x318/0x330 __x64_sys_sendto+0x76/0x90 x64_sys_call+0x14e8/0x1c00 do_syscall_64+0x9e/0x1a0 entry_SYSCALL_64_after_hwframe+0x77/0x7f value changed: 0x00000000fffbac6e -> 0x00000000fffbac6f Reported by Kernel Concurrency Sanitizer on: CPU: 2 UID: 0 PID: 287 Comm: mausezahn Not tainted 6.13.0-rc7-01544-gb4b270f11a02 #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 [2] #!/bin/bash set +H echo whitelist > /sys/kernel/debug/kcsan echo !vxlan_xmit > /sys/kernel/debug/kcsan ip link add name vx0 up type vxlan id 10010 dstport 4789 local 192.0.2.1 bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 198.51.100.1 taskset -c 0 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q & taskset -c 2 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q & | medium |
| CVE-2025-38036 | In the Linux kernel, the following vulnerability has been resolved: drm/xe/vf: Perform early GT MMIO initialization to read GMDID VFs need to communicate with the GuC to obtain the GMDID value and existing GuC functions used for that assume that the GT has it's MMIO members already setup. However, due to recent refactoring the gt->mmio is initialized later, and any attempt by the VF to use xe_mmio_read|write() from GuC functions will lead to NPD crash due to unset MMIO register address: [] xe 0000:00:02.1: [drm] Running in SR-IOV VF mode [] xe 0000:00:02.1: [drm] GT0: sending H2G MMIO 0x5507 [] BUG: unable to handle page fault for address: 0000000000190240 Since we are already tweaking the id and type of the primary GT to mimic it's a Media GT before initializing the GuC communication, we can also call xe_gt_mmio_init() to perform early setup of the gt->mmio which will make those GuC functions work again. | medium |
| CVE-2025-38035 | In the Linux kernel, the following vulnerability has been resolved: nvmet-tcp: don't restore null sk_state_change queue->state_change is set as part of nvmet_tcp_set_queue_sock(), but if the TCP connection isn't established when nvmet_tcp_set_queue_sock() is called then queue->state_change isn't set and sock->sk->sk_state_change isn't replaced. As such we don't need to restore sock->sk->sk_state_change if queue->state_change is NULL. This avoids NULL pointer dereferences such as this: [ 286.462026][ C0] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 286.462814][ C0] #PF: supervisor instruction fetch in kernel mode [ 286.463796][ C0] #PF: error_code(0x0010) - not-present page [ 286.464392][ C0] PGD 8000000140620067 P4D 8000000140620067 PUD 114201067 PMD 0 [ 286.465086][ C0] Oops: Oops: 0010 [#1] SMP KASAN PTI [ 286.465559][ C0] CPU: 0 UID: 0 PID: 1628 Comm: nvme Not tainted 6.15.0-rc2+ #11 PREEMPT(voluntary) [ 286.466393][ C0] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 [ 286.467147][ C0] RIP: 0010:0x0 [ 286.467420][ C0] Code: Unable to access opcode bytes at 0xffffffffffffffd6. [ 286.467977][ C0] RSP: 0018:ffff8883ae008580 EFLAGS: 00010246 [ 286.468425][ C0] RAX: 0000000000000000 RBX: ffff88813fd34100 RCX: ffffffffa386cc43 [ 286.469019][ C0] RDX: 1ffff11027fa68b6 RSI: 0000000000000008 RDI: ffff88813fd34100 [ 286.469545][ C0] RBP: ffff88813fd34160 R08: 0000000000000000 R09: ffffed1027fa682c [ 286.470072][ C0] R10: ffff88813fd34167 R11: 0000000000000000 R12: ffff88813fd344c3 [ 286.470585][ C0] R13: ffff88813fd34112 R14: ffff88813fd34aec R15: ffff888132cdd268 [ 286.471070][ C0] FS: 00007fe3c04c7d80(0000) GS:ffff88840743f000(0000) knlGS:0000000000000000 [ 286.471644][ C0] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 286.472543][ C0] CR2: ffffffffffffffd6 CR3: 000000012daca000 CR4: 00000000000006f0 [ 286.473500][ C0] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 286.474467][ C0] DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400 [ 286.475453][ C0] Call Trace: [ 286.476102][ C0] <IRQ> [ 286.476719][ C0] tcp_fin+0x2bb/0x440 [ 286.477429][ C0] tcp_data_queue+0x190f/0x4e60 [ 286.478174][ C0] ? __build_skb_around+0x234/0x330 [ 286.478940][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.479659][ C0] ? __pfx_tcp_data_queue+0x10/0x10 [ 286.480431][ C0] ? tcp_try_undo_loss+0x640/0x6c0 [ 286.481196][ C0] ? seqcount_lockdep_reader_access.constprop.0+0x82/0x90 [ 286.482046][ C0] ? kvm_clock_get_cycles+0x14/0x30 [ 286.482769][ C0] ? ktime_get+0x66/0x150 [ 286.483433][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.484146][ C0] tcp_rcv_established+0x6e4/0x2050 [ 286.484857][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.485523][ C0] ? ipv4_dst_check+0x160/0x2b0 [ 286.486203][ C0] ? __pfx_tcp_rcv_established+0x10/0x10 [ 286.486917][ C0] ? lock_release+0x217/0x2c0 [ 286.487595][ C0] tcp_v4_do_rcv+0x4d6/0x9b0 [ 286.488279][ C0] tcp_v4_rcv+0x2af8/0x3e30 [ 286.488904][ C0] ? raw_local_deliver+0x51b/0xad0 [ 286.489551][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.490198][ C0] ? __pfx_tcp_v4_rcv+0x10/0x10 [ 286.490813][ C0] ? __pfx_raw_local_deliver+0x10/0x10 [ 286.491487][ C0] ? __pfx_nf_confirm+0x10/0x10 [nf_conntrack] [ 286.492275][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.492900][ C0] ip_protocol_deliver_rcu+0x8f/0x370 [ 286.493579][ C0] ip_local_deliver_finish+0x297/0x420 [ 286.494268][ C0] ip_local_deliver+0x168/0x430 [ 286.494867][ C0] ? __pfx_ip_local_deliver+0x10/0x10 [ 286.495498][ C0] ? __pfx_ip_local_deliver_finish+0x10/0x10 [ 286.496204][ C0] ? ip_rcv_finish_core+0x19a/0x1f20 [ 286.496806][ C0] ? lock_release+0x217/0x2c0 [ 286.497414][ C0] ip_rcv+0x455/0x6e0 [ 286.497945][ C0] ? __pfx_ip_rcv+0x10/0x10 [ ---truncated--- | medium |
| CVE-2025-38034 | In the Linux kernel, the following vulnerability has been resolved: btrfs: correct the order of prelim_ref arguments in btrfs__prelim_ref btrfs_prelim_ref() calls the old and new reference variables in the incorrect order. This causes a NULL pointer dereference because oldref is passed as NULL to trace_btrfs_prelim_ref_insert(). Note, trace_btrfs_prelim_ref_insert() is being called with newref as oldref (and oldref as NULL) on purpose in order to print out the values of newref. To reproduce: echo 1 > /sys/kernel/debug/tracing/events/btrfs/btrfs_prelim_ref_insert/enable Perform some writeback operations. Backtrace: BUG: kernel NULL pointer dereference, address: 0000000000000018 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 115949067 P4D 115949067 PUD 11594a067 PMD 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 1 UID: 0 PID: 1188 Comm: fsstress Not tainted 6.15.0-rc2-tester+ #47 PREEMPT(voluntary) 7ca2cef72d5e9c600f0c7718adb6462de8149622 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-2-gc13ff2cd-prebuilt.qemu.org 04/01/2014 RIP: 0010:trace_event_raw_event_btrfs__prelim_ref+0x72/0x130 Code: e8 43 81 9f ff 48 85 c0 74 78 4d 85 e4 0f 84 8f 00 00 00 49 8b 94 24 c0 06 00 00 48 8b 0a 48 89 48 08 48 8b 52 08 48 89 50 10 <49> 8b 55 18 48 89 50 18 49 8b 55 20 48 89 50 20 41 0f b6 55 28 88 RSP: 0018:ffffce44820077a0 EFLAGS: 00010286 RAX: ffff8c6b403f9014 RBX: ffff8c6b55825730 RCX: 304994edf9cf506b RDX: d8b11eb7f0fdb699 RSI: ffff8c6b403f9010 RDI: ffff8c6b403f9010 RBP: 0000000000000001 R08: 0000000000000001 R09: 0000000000000010 R10: 00000000ffffffff R11: 0000000000000000 R12: ffff8c6b4e8fb000 R13: 0000000000000000 R14: ffffce44820077a8 R15: ffff8c6b4abd1540 FS: 00007f4dc6813740(0000) GS:ffff8c6c1d378000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000018 CR3: 000000010eb42000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> prelim_ref_insert+0x1c1/0x270 find_parent_nodes+0x12a6/0x1ee0 ? __entry_text_end+0x101f06/0x101f09 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 btrfs_is_data_extent_shared+0x167/0x640 ? fiemap_process_hole+0xd0/0x2c0 extent_fiemap+0xa5c/0xbc0 ? __entry_text_end+0x101f05/0x101f09 btrfs_fiemap+0x7e/0xd0 do_vfs_ioctl+0x425/0x9d0 __x64_sys_ioctl+0x75/0xc0 | medium |
| CVE-2025-38033 | In the Linux kernel, the following vulnerability has been resolved: x86/Kconfig: make CFI_AUTO_DEFAULT depend on !RUST or Rust >= 1.88 Calling core::fmt::write() from rust code while FineIBT is enabled results in a kernel panic: [ 4614.199779] kernel BUG at arch/x86/kernel/cet.c:132! [ 4614.205343] Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI [ 4614.211781] CPU: 2 UID: 0 PID: 6057 Comm: dmabuf_dump Tainted: G U O 6.12.17-android16-0-g6ab38c534a43 #1 9da040f27673ec3945e23b998a0f8bd64c846599 [ 4614.227832] Tainted: [U]=USER, [O]=OOT_MODULE [ 4614.241247] RIP: 0010:do_kernel_cp_fault+0xea/0xf0 ... [ 4614.398144] RIP: 0010:_RNvXs5_NtNtNtCs3o2tGsuHyou_4core3fmt3num3impyNtB9_7Display3fmt+0x0/0x20 [ 4614.407792] Code: 48 f7 df 48 0f 48 f9 48 89 f2 89 c6 5d e9 18 fd ff ff 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 41 81 ea 14 61 af 2c 74 03 0f 0b 90 <66> 0f 1f 00 55 48 89 e5 48 89 f2 48 8b 3f be 01 00 00 00 5d e9 e7 [ 4614.428775] RSP: 0018:ffffb95acfa4ba68 EFLAGS: 00010246 [ 4614.434609] RAX: 0000000000000000 RBX: 0000000000000010 RCX: 0000000000000000 [ 4614.442587] RDX: 0000000000000007 RSI: ffffb95acfa4ba70 RDI: ffffb95acfa4bc88 [ 4614.450557] RBP: ffffb95acfa4bae0 R08: ffff0a00ffffff05 R09: 0000000000000070 [ 4614.458527] R10: 0000000000000000 R11: ffffffffab67eaf0 R12: ffffb95acfa4bcc8 [ 4614.466493] R13: ffffffffac5d50f0 R14: 0000000000000000 R15: 0000000000000000 [ 4614.474473] ? __cfi__RNvXs5_NtNtNtCs3o2tGsuHyou_4core3fmt3num3impyNtB9_7Display3fmt+0x10/0x10 [ 4614.484118] ? _RNvNtCs3o2tGsuHyou_4core3fmt5write+0x1d2/0x250 This happens because core::fmt::write() calls core::fmt::rt::Argument::fmt(), which currently has CFI disabled: library/core/src/fmt/rt.rs: 171 // FIXME: Transmuting formatter in new and indirectly branching to/calling 172 // it here is an explicit CFI violation. 173 #[allow(inline_no_sanitize)] 174 #[no_sanitize(cfi, kcfi)] 175 #[inline] 176 pub(super) unsafe fn fmt(&self, f: &mut Formatter<'_>) -> Result { This causes a Control Protection exception, because FineIBT has sealed off the original function's endbr64. This makes rust currently incompatible with FineIBT. Add a Kconfig dependency that prevents FineIBT from getting turned on by default if rust is enabled. [ Rust 1.88.0 (scheduled for 2025-06-26) should have this fixed [1], and thus we relaxed the condition with Rust >= 1.88. When `objtool` lands checking for this with e.g. [2], the plan is to ideally run that in upstream Rust's CI to prevent regressions early [3], since we do not control `core`'s source code. Alice tested the Rust PR backported to an older compiler. Peter would like that Rust provides a stable `core` which can be pulled into the kernel: "Relying on that much out of tree code is 'unfortunate'". - Miguel ] [ Reduced splat. - Miguel ] | high |
| CVE-2025-38032 | In the Linux kernel, the following vulnerability has been resolved: mr: consolidate the ipmr_can_free_table() checks. Guoyu Yin reported a splat in the ipmr netns cleanup path: WARNING: CPU: 2 PID: 14564 at net/ipv4/ipmr.c:440 ipmr_free_table net/ipv4/ipmr.c:440 [inline] WARNING: CPU: 2 PID: 14564 at net/ipv4/ipmr.c:440 ipmr_rules_exit+0x135/0x1c0 net/ipv4/ipmr.c:361 Modules linked in: CPU: 2 UID: 0 PID: 14564 Comm: syz.4.838 Not tainted 6.14.0 #1 Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:ipmr_free_table net/ipv4/ipmr.c:440 [inline] RIP: 0010:ipmr_rules_exit+0x135/0x1c0 net/ipv4/ipmr.c:361 Code: ff df 48 c1 ea 03 80 3c 02 00 75 7d 48 c7 83 60 05 00 00 00 00 00 00 5b 5d 41 5c 41 5d 41 5e e9 71 67 7f 00 e8 4c 2d 8a fd 90 <0f> 0b 90 eb 93 e8 41 2d 8a fd 0f b6 2d 80 54 ea 01 31 ff 89 ee e8 RSP: 0018:ffff888109547c58 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffff888108c12dc0 RCX: ffffffff83e09868 RDX: ffff8881022b3300 RSI: ffffffff83e098d4 RDI: 0000000000000005 RBP: ffff888104288000 R08: 0000000000000000 R09: ffffed10211825c9 R10: 0000000000000001 R11: ffff88801816c4a0 R12: 0000000000000001 R13: ffff888108c13320 R14: ffff888108c12dc0 R15: fffffbfff0b74058 FS: 00007f84f39316c0(0000) GS:ffff88811b100000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f84f3930f98 CR3: 0000000113b56000 CR4: 0000000000350ef0 Call Trace: <TASK> ipmr_net_exit_batch+0x50/0x90 net/ipv4/ipmr.c:3160 ops_exit_list+0x10c/0x160 net/core/net_namespace.c:177 setup_net+0x47d/0x8e0 net/core/net_namespace.c:394 copy_net_ns+0x25d/0x410 net/core/net_namespace.c:516 create_new_namespaces+0x3f6/0xaf0 kernel/nsproxy.c:110 unshare_nsproxy_namespaces+0xc3/0x180 kernel/nsproxy.c:228 ksys_unshare+0x78d/0x9a0 kernel/fork.c:3342 __do_sys_unshare kernel/fork.c:3413 [inline] __se_sys_unshare kernel/fork.c:3411 [inline] __x64_sys_unshare+0x31/0x40 kernel/fork.c:3411 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xa6/0x1a0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f84f532cc29 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f84f3931038 EFLAGS: 00000246 ORIG_RAX: 0000000000000110 RAX: ffffffffffffffda RBX: 00007f84f5615fa0 RCX: 00007f84f532cc29 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000040000400 RBP: 00007f84f53fba18 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 00007f84f5615fa0 R15: 00007fff51c5f328 </TASK> The running kernel has CONFIG_IP_MROUTE_MULTIPLE_TABLES disabled, and the sanity check for such build is still too loose. Address the issue consolidating the relevant sanity check in a single helper regardless of the kernel configuration. Also share it between the ipv4 and ipv6 code. | high |
| CVE-2025-38031 | In the Linux kernel, the following vulnerability has been resolved: padata: do not leak refcount in reorder_work A recent patch that addressed a UAF introduced a reference count leak: the parallel_data refcount is incremented unconditionally, regardless of the return value of queue_work(). If the work item is already queued, the incremented refcount is never decremented. Fix this by checking the return value of queue_work() and decrementing the refcount when necessary. Resolves: Unreferenced object 0xffff9d9f421e3d80 (size 192): comm "cryptomgr_probe", pid 157, jiffies 4294694003 hex dump (first 32 bytes): 80 8b cf 41 9f 9d ff ff b8 97 e0 89 ff ff ff ff ...A............ d0 97 e0 89 ff ff ff ff 19 00 00 00 1f 88 23 00 ..............#. backtrace (crc 838fb36): __kmalloc_cache_noprof+0x284/0x320 padata_alloc_pd+0x20/0x1e0 padata_alloc_shell+0x3b/0xa0 0xffffffffc040a54d cryptomgr_probe+0x43/0xc0 kthread+0xf6/0x1f0 ret_from_fork+0x2f/0x50 ret_from_fork_asm+0x1a/0x30 | medium |
| CVE-2025-38029 | In the Linux kernel, the following vulnerability has been resolved: kasan: avoid sleepable page allocation from atomic context apply_to_pte_range() enters the lazy MMU mode and then invokes kasan_populate_vmalloc_pte() callback on each page table walk iteration. However, the callback can go into sleep when trying to allocate a single page, e.g. if an architecutre disables preemption on lazy MMU mode enter. On s390 if make arch_enter_lazy_mmu_mode() -> preempt_enable() and arch_leave_lazy_mmu_mode() -> preempt_disable(), such crash occurs: [ 0.663336] BUG: sleeping function called from invalid context at ./include/linux/sched/mm.h:321 [ 0.663348] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 2, name: kthreadd [ 0.663358] preempt_count: 1, expected: 0 [ 0.663366] RCU nest depth: 0, expected: 0 [ 0.663375] no locks held by kthreadd/2. [ 0.663383] Preemption disabled at: [ 0.663386] [<0002f3284cbb4eda>] apply_to_pte_range+0xfa/0x4a0 [ 0.663405] CPU: 0 UID: 0 PID: 2 Comm: kthreadd Not tainted 6.15.0-rc5-gcc-kasan-00043-gd76bb1ebb558-dirty #162 PREEMPT [ 0.663408] Hardware name: IBM 3931 A01 701 (KVM/Linux) [ 0.663409] Call Trace: [ 0.663410] [<0002f3284c385f58>] dump_stack_lvl+0xe8/0x140 [ 0.663413] [<0002f3284c507b9e>] __might_resched+0x66e/0x700 [ 0.663415] [<0002f3284cc4f6c0>] __alloc_frozen_pages_noprof+0x370/0x4b0 [ 0.663419] [<0002f3284ccc73c0>] alloc_pages_mpol+0x1a0/0x4a0 [ 0.663421] [<0002f3284ccc8518>] alloc_frozen_pages_noprof+0x88/0xc0 [ 0.663424] [<0002f3284ccc8572>] alloc_pages_noprof+0x22/0x120 [ 0.663427] [<0002f3284cc341ac>] get_free_pages_noprof+0x2c/0xc0 [ 0.663429] [<0002f3284cceba70>] kasan_populate_vmalloc_pte+0x50/0x120 [ 0.663433] [<0002f3284cbb4ef8>] apply_to_pte_range+0x118/0x4a0 [ 0.663435] [<0002f3284cbc7c14>] apply_to_pmd_range+0x194/0x3e0 [ 0.663437] [<0002f3284cbc99be>] __apply_to_page_range+0x2fe/0x7a0 [ 0.663440] [<0002f3284cbc9e88>] apply_to_page_range+0x28/0x40 [ 0.663442] [<0002f3284ccebf12>] kasan_populate_vmalloc+0x82/0xa0 [ 0.663445] [<0002f3284cc1578c>] alloc_vmap_area+0x34c/0xc10 [ 0.663448] [<0002f3284cc1c2a6>] __get_vm_area_node+0x186/0x2a0 [ 0.663451] [<0002f3284cc1e696>] __vmalloc_node_range_noprof+0x116/0x310 [ 0.663454] [<0002f3284cc1d950>] __vmalloc_node_noprof+0xd0/0x110 [ 0.663457] [<0002f3284c454b88>] alloc_thread_stack_node+0xf8/0x330 [ 0.663460] [<0002f3284c458d56>] dup_task_struct+0x66/0x4d0 [ 0.663463] [<0002f3284c45be90>] copy_process+0x280/0x4b90 [ 0.663465] [<0002f3284c460940>] kernel_clone+0xd0/0x4b0 [ 0.663467] [<0002f3284c46115e>] kernel_thread+0xbe/0xe0 [ 0.663469] [<0002f3284c4e440e>] kthreadd+0x50e/0x7f0 [ 0.663472] [<0002f3284c38c04a>] __ret_from_fork+0x8a/0xf0 [ 0.663475] [<0002f3284ed57ff2>] ret_from_fork+0xa/0x38 Instead of allocating single pages per-PTE, bulk-allocate the shadow memory prior to applying kasan_populate_vmalloc_pte() callback on a page range. | medium |
| CVE-2025-38028 | In the Linux kernel, the following vulnerability has been resolved: NFS/localio: Fix a race in nfs_local_open_fh() Once the clp->cl_uuid.lock has been dropped, another CPU could come in and free the struct nfsd_file that was just added. To prevent that from happening, take the RCU read lock before dropping the spin lock. | medium |
| CVE-2025-38027 | In the Linux kernel, the following vulnerability has been resolved: regulator: max20086: fix invalid memory access max20086_parse_regulators_dt() calls of_regulator_match() using an array of struct of_regulator_match allocated on the stack for the matches argument. of_regulator_match() calls devm_of_regulator_put_matches(), which calls devres_alloc() to allocate a struct devm_of_regulator_matches which will be de-allocated using devm_of_regulator_put_matches(). struct devm_of_regulator_matches is populated with the stack allocated matches array. If the device fails to probe, devm_of_regulator_put_matches() will be called and will try to call of_node_put() on that stack pointer, generating the following dmesg entries: max20086 6-0028: Failed to read DEVICE_ID reg: -121 kobject: '\xc0$\xa5\x03' (000000002cebcb7a): is not initialized, yet kobject_put() is being called. Followed by a stack trace matching the call flow described above. Switch to allocating the matches array using devm_kcalloc() to avoid accessing the stack pointer long after it's out of scope. This also has the advantage of allowing multiple max20086 to probe without overriding the data stored inside the global of_regulator_match. | medium |
| CVE-2025-38026 | Rejected reason: This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. | No Score |
| CVE-2025-38025 | In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad7606: check for NULL before calling sw_mode_config() Check that the sw_mode_config function pointer is not NULL before calling it. Not all buses define this callback, which resulted in a NULL pointer dereference. | medium |
| CVE-2025-38024 | In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Fix slab-use-after-free Read in rxe_queue_cleanup bug Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x7d/0xa0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xcf/0x610 mm/kasan/report.c:489 kasan_report+0xb5/0xe0 mm/kasan/report.c:602 rxe_queue_cleanup+0xd0/0xe0 drivers/infiniband/sw/rxe/rxe_queue.c:195 rxe_cq_cleanup+0x3f/0x50 drivers/infiniband/sw/rxe/rxe_cq.c:132 __rxe_cleanup+0x168/0x300 drivers/infiniband/sw/rxe/rxe_pool.c:232 rxe_create_cq+0x22e/0x3a0 drivers/infiniband/sw/rxe/rxe_verbs.c:1109 create_cq+0x658/0xb90 drivers/infiniband/core/uverbs_cmd.c:1052 ib_uverbs_create_cq+0xc7/0x120 drivers/infiniband/core/uverbs_cmd.c:1095 ib_uverbs_write+0x969/0xc90 drivers/infiniband/core/uverbs_main.c:679 vfs_write fs/read_write.c:677 [inline] vfs_write+0x26a/0xcc0 fs/read_write.c:659 ksys_write+0x1b8/0x200 fs/read_write.c:731 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xaa/0x1b0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f In the function rxe_create_cq, when rxe_cq_from_init fails, the function rxe_cleanup will be called to handle the allocated resources. In fact, some memory resources have already been freed in the function rxe_cq_from_init. Thus, this problem will occur. The solution is to let rxe_cleanup do all the work. | medium |
| CVE-2025-38023 | In the Linux kernel, the following vulnerability has been resolved: nfs: handle failure of nfs_get_lock_context in unlock path When memory is insufficient, the allocation of nfs_lock_context in nfs_get_lock_context() fails and returns -ENOMEM. If we mistakenly treat an nfs4_unlockdata structure (whose l_ctx member has been set to -ENOMEM) as valid and proceed to execute rpc_run_task(), this will trigger a NULL pointer dereference in nfs4_locku_prepare. For example: BUG: kernel NULL pointer dereference, address: 000000000000000c PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI CPU: 15 UID: 0 PID: 12 Comm: kworker/u64:0 Not tainted 6.15.0-rc2-dirty #60 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 Workqueue: rpciod rpc_async_schedule RIP: 0010:nfs4_locku_prepare+0x35/0xc2 Code: 89 f2 48 89 fd 48 c7 c7 68 69 ef b5 53 48 8b 8e 90 00 00 00 48 89 f3 RSP: 0018:ffffbbafc006bdb8 EFLAGS: 00010246 RAX: 000000000000004b RBX: ffff9b964fc1fa00 RCX: 0000000000000000 RDX: 0000000000000000 RSI: fffffffffffffff4 RDI: ffff9ba53fddbf40 RBP: ffff9ba539934000 R08: 0000000000000000 R09: ffffbbafc006bc38 R10: ffffffffb6b689c8 R11: 0000000000000003 R12: ffff9ba539934030 R13: 0000000000000001 R14: 0000000004248060 R15: ffffffffb56d1c30 FS: 0000000000000000(0000) GS:ffff9ba5881f0000(0000) knlGS:00000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000000c CR3: 000000093f244000 CR4: 00000000000006f0 Call Trace: <TASK> __rpc_execute+0xbc/0x480 rpc_async_schedule+0x2f/0x40 process_one_work+0x232/0x5d0 worker_thread+0x1da/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0x10d/0x240 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x34/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Modules linked in: CR2: 000000000000000c ---[ end trace 0000000000000000 ]--- Free the allocated nfs4_unlockdata when nfs_get_lock_context() fails and return NULL to terminate subsequent rpc_run_task, preventing NULL pointer dereference. | medium |
| CVE-2025-38022 | In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Fix "KASAN: slab-use-after-free Read in ib_register_device" problem Call Trace: __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xc3/0x670 mm/kasan/report.c:521 kasan_report+0xe0/0x110 mm/kasan/report.c:634 strlen+0x93/0xa0 lib/string.c:420 __fortify_strlen include/linux/fortify-string.h:268 [inline] get_kobj_path_length lib/kobject.c:118 [inline] kobject_get_path+0x3f/0x2a0 lib/kobject.c:158 kobject_uevent_env+0x289/0x1870 lib/kobject_uevent.c:545 ib_register_device drivers/infiniband/core/device.c:1472 [inline] ib_register_device+0x8cf/0xe00 drivers/infiniband/core/device.c:1393 rxe_register_device+0x275/0x320 drivers/infiniband/sw/rxe/rxe_verbs.c:1552 rxe_net_add+0x8e/0xe0 drivers/infiniband/sw/rxe/rxe_net.c:550 rxe_newlink+0x70/0x190 drivers/infiniband/sw/rxe/rxe.c:225 nldev_newlink+0x3a3/0x680 drivers/infiniband/core/nldev.c:1796 rdma_nl_rcv_msg+0x387/0x6e0 drivers/infiniband/core/netlink.c:195 rdma_nl_rcv_skb.constprop.0.isra.0+0x2e5/0x450 netlink_unicast_kernel net/netlink/af_netlink.c:1313 [inline] netlink_unicast+0x53a/0x7f0 net/netlink/af_netlink.c:1339 netlink_sendmsg+0x8d1/0xdd0 net/netlink/af_netlink.c:1883 sock_sendmsg_nosec net/socket.c:712 [inline] __sock_sendmsg net/socket.c:727 [inline] ____sys_sendmsg+0xa95/0xc70 net/socket.c:2566 ___sys_sendmsg+0x134/0x1d0 net/socket.c:2620 __sys_sendmsg+0x16d/0x220 net/socket.c:2652 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xcd/0x260 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f This problem is similar to the problem that the commit 1d6a9e7449e2 ("RDMA/core: Fix use-after-free when rename device name") fixes. The root cause is: the function ib_device_rename() renames the name with lock. But in the function kobject_uevent(), this name is accessed without lock protection at the same time. The solution is to add the lock protection when this name is accessed in the function kobject_uevent(). | medium |
| CVE-2025-38021 | In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix null check of pipe_ctx->plane_state for update_dchubp_dpp Similar to commit 6a057072ddd1 ("drm/amd/display: Fix null check for pipe_ctx->plane_state in dcn20_program_pipe") that addresses a null pointer dereference on dcn20_update_dchubp_dpp. This is the same function hooked for update_dchubp_dpp in dcn401, with the same issue. Fix possible null pointer deference on dcn401_program_pipe too. (cherry picked from commit d8d47f739752227957d8efc0cb894761bfe1d879) | medium |
| CVE-2025-38020 | In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Disable MACsec offload for uplink representor profile MACsec offload is not supported in switchdev mode for uplink representors. When switching to the uplink representor profile, the MACsec offload feature must be cleared from the netdevice's features. If left enabled, attempts to add offloads result in a null pointer dereference, as the uplink representor does not support MACsec offload even though the feature bit remains set. Clear NETIF_F_HW_MACSEC in mlx5e_fix_uplink_rep_features(). Kernel log: Oops: general protection fault, probably for non-canonical address 0xdffffc000000000f: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000078-0x000000000000007f] CPU: 29 UID: 0 PID: 4714 Comm: ip Not tainted 6.14.0-rc4_for_upstream_debug_2025_03_02_17_35 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:__mutex_lock+0x128/0x1dd0 Code: d0 7c 08 84 d2 0f 85 ad 15 00 00 8b 35 91 5c fe 03 85 f6 75 29 49 8d 7e 60 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 a6 15 00 00 4d 3b 76 60 0f 85 fd 0b 00 00 65 ff RSP: 0018:ffff888147a4f160 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000001 RDX: 000000000000000f RSI: 0000000000000000 RDI: 0000000000000078 RBP: ffff888147a4f2e0 R08: ffffffffa05d2c19 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000 R13: dffffc0000000000 R14: 0000000000000018 R15: ffff888152de0000 FS: 00007f855e27d800(0000) GS:ffff88881ee80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004e5768 CR3: 000000013ae7c005 CR4: 0000000000372eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 Call Trace: <TASK> ? die_addr+0x3d/0xa0 ? exc_general_protection+0x144/0x220 ? asm_exc_general_protection+0x22/0x30 ? mlx5e_macsec_add_secy+0xf9/0x700 [mlx5_core] ? __mutex_lock+0x128/0x1dd0 ? lockdep_set_lock_cmp_fn+0x190/0x190 ? mlx5e_macsec_add_secy+0xf9/0x700 [mlx5_core] ? mutex_lock_io_nested+0x1ae0/0x1ae0 ? lock_acquire+0x1c2/0x530 ? macsec_upd_offload+0x145/0x380 ? lockdep_hardirqs_on_prepare+0x400/0x400 ? kasan_save_stack+0x30/0x40 ? kasan_save_stack+0x20/0x40 ? kasan_save_track+0x10/0x30 ? __kasan_kmalloc+0x77/0x90 ? __kmalloc_noprof+0x249/0x6b0 ? genl_family_rcv_msg_attrs_parse.constprop.0+0xb5/0x240 ? mlx5e_macsec_add_secy+0xf9/0x700 [mlx5_core] mlx5e_macsec_add_secy+0xf9/0x700 [mlx5_core] ? mlx5e_macsec_add_rxsa+0x11a0/0x11a0 [mlx5_core] macsec_update_offload+0x26c/0x820 ? macsec_set_mac_address+0x4b0/0x4b0 ? lockdep_hardirqs_on_prepare+0x284/0x400 ? _raw_spin_unlock_irqrestore+0x47/0x50 macsec_upd_offload+0x2c8/0x380 ? macsec_update_offload+0x820/0x820 ? __nla_parse+0x22/0x30 ? genl_family_rcv_msg_attrs_parse.constprop.0+0x15e/0x240 genl_family_rcv_msg_doit+0x1cc/0x2a0 ? genl_family_rcv_msg_attrs_parse.constprop.0+0x240/0x240 ? cap_capable+0xd4/0x330 genl_rcv_msg+0x3ea/0x670 ? genl_family_rcv_msg_dumpit+0x2a0/0x2a0 ? lockdep_set_lock_cmp_fn+0x190/0x190 ? macsec_update_offload+0x820/0x820 netlink_rcv_skb+0x12b/0x390 ? genl_family_rcv_msg_dumpit+0x2a0/0x2a0 ? netlink_ack+0xd80/0xd80 ? rwsem_down_read_slowpath+0xf90/0xf90 ? netlink_deliver_tap+0xcd/0xac0 ? netlink_deliver_tap+0x155/0xac0 ? _copy_from_iter+0x1bb/0x12c0 genl_rcv+0x24/0x40 netlink_unicast+0x440/0x700 ? netlink_attachskb+0x760/0x760 ? lock_acquire+0x1c2/0x530 ? __might_fault+0xbb/0x170 netlink_sendmsg+0x749/0xc10 ? netlink_unicast+0x700/0x700 ? __might_fault+0xbb/0x170 ? netlink_unicast+0x700/0x700 __sock_sendmsg+0xc5/0x190 ____sys_sendmsg+0x53f/0x760 ? import_iovec+0x7/0x10 ? kernel_sendmsg+0x30/0x30 ? __copy_msghdr+0x3c0/0x3c0 ? filter_irq_stacks+0x90/0x90 ? stack_depot_save_flags+0x28/0xa30 ___sys_sen ---truncated--- | medium |
| CVE-2025-38019 | In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_router: Fix use-after-free when deleting GRE net devices The driver only offloads neighbors that are constructed on top of net devices registered by it or their uppers (which are all Ethernet). The device supports GRE encapsulation and decapsulation of forwarded traffic, but the driver will not offload dummy neighbors constructed on top of GRE net devices as they are not uppers of its net devices: # ip link add name gre1 up type gre tos inherit local 192.0.2.1 remote 198.51.100.1 # ip neigh add 0.0.0.0 lladdr 0.0.0.0 nud noarp dev gre1 $ ip neigh show dev gre1 nud noarp 0.0.0.0 lladdr 0.0.0.0 NOARP (Note that the neighbor is not marked with 'offload') When the driver is reloaded and the existing configuration is replayed, the driver does not perform the same check regarding existing neighbors and offloads the previously added one: # devlink dev reload pci/0000:01:00.0 $ ip neigh show dev gre1 nud noarp 0.0.0.0 lladdr 0.0.0.0 offload NOARP If the neighbor is later deleted, the driver will ignore the notification (given the GRE net device is not its upper) and will therefore keep referencing freed memory, resulting in a use-after-free [1] when the net device is deleted: # ip neigh del 0.0.0.0 lladdr 0.0.0.0 dev gre1 # ip link del dev gre1 Fix by skipping neighbor replay if the net device for which the replay is performed is not our upper. [1] BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x1ea/0x200 Read of size 8 at addr ffff888155b0e420 by task ip/2282 [...] Call Trace: <TASK> dump_stack_lvl+0x6f/0xa0 print_address_description.constprop.0+0x6f/0x350 print_report+0x108/0x205 kasan_report+0xdf/0x110 mlxsw_sp_neigh_entry_update+0x1ea/0x200 mlxsw_sp_router_rif_gone_sync+0x2a8/0x440 mlxsw_sp_rif_destroy+0x1e9/0x750 mlxsw_sp_netdevice_ipip_ol_event+0x3c9/0xdc0 mlxsw_sp_router_netdevice_event+0x3ac/0x15e0 notifier_call_chain+0xca/0x150 call_netdevice_notifiers_info+0x7f/0x100 unregister_netdevice_many_notify+0xc8c/0x1d90 rtnl_dellink+0x34e/0xa50 rtnetlink_rcv_msg+0x6fb/0xb70 netlink_rcv_skb+0x131/0x360 netlink_unicast+0x426/0x710 netlink_sendmsg+0x75a/0xc20 __sock_sendmsg+0xc1/0x150 ____sys_sendmsg+0x5aa/0x7b0 ___sys_sendmsg+0xfc/0x180 __sys_sendmsg+0x121/0x1b0 do_syscall_64+0xbb/0x1d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 | high |
| CVE-2025-38018 | In the Linux kernel, the following vulnerability has been resolved: net/tls: fix kernel panic when alloc_page failed We cannot set frag_list to NULL pointer when alloc_page failed. It will be used in tls_strp_check_queue_ok when the next time tls_strp_read_sock is called. This is because we don't reset full_len in tls_strp_flush_anchor_copy() so the recv path will try to continue handling the partial record on the next call but we dettached the rcvq from the frag list. Alternative fix would be to reset full_len. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000028 Call trace: tls_strp_check_rcv+0x128/0x27c tls_strp_data_ready+0x34/0x44 tls_data_ready+0x3c/0x1f0 tcp_data_ready+0x9c/0xe4 tcp_data_queue+0xf6c/0x12d0 tcp_rcv_established+0x52c/0x798 | medium |
| CVE-2025-38017 | In the Linux kernel, the following vulnerability has been resolved: fs/eventpoll: fix endless busy loop after timeout has expired After commit 0a65bc27bd64 ("eventpoll: Set epoll timeout if it's in the future"), the following program would immediately enter a busy loop in the kernel: ``` int main() { int e = epoll_create1(0); struct epoll_event event = {.events = EPOLLIN}; epoll_ctl(e, EPOLL_CTL_ADD, 0, &event); const struct timespec timeout = {.tv_nsec = 1}; epoll_pwait2(e, &event, 1, &timeout, 0); } ``` This happens because the given (non-zero) timeout of 1 nanosecond usually expires before ep_poll() is entered and then ep_schedule_timeout() returns false, but `timed_out` is never set because the code line that sets it is skipped. This quickly turns into a soft lockup, RCU stalls and deadlocks, inflicting severe headaches to the whole system. When the timeout has expired, we don't need to schedule a hrtimer, but we should set the `timed_out` variable. Therefore, I suggest moving the ep_schedule_timeout() check into the `timed_out` expression instead of skipping it. brauner: Note that there was an earlier fix by Joe Damato in response to my bug report in [1]. | medium |
| CVE-2025-38016 | In the Linux kernel, the following vulnerability has been resolved: HID: bpf: abort dispatch if device destroyed The current HID bpf implementation assumes no output report/request will go through it after hid_bpf_destroy_device() has been called. This leads to a bug that unplugging certain types of HID devices causes a cleaned- up SRCU to be accessed. The bug was previously a hidden failure until a recent x86 percpu change [1] made it access not-present pages. The bug will be triggered if the conditions below are met: A) a device under the driver has some LEDs on B) hid_ll_driver->request() is uninplemented (e.g., logitech-djreceiver) If condition A is met, hidinput_led_worker() is always scheduled *after* hid_bpf_destroy_device(). hid_destroy_device ` hid_bpf_destroy_device ` cleanup_srcu_struct(&hdev->bpf.srcu) ` hid_remove_device ` ... ` led_classdev_unregister ` led_trigger_set(led_cdev, NULL) ` led_set_brightness(led_cdev, LED_OFF) ` ... ` input_inject_event ` input_event_dispose ` hidinput_input_event ` schedule_work(&hid->led_work) [hidinput_led_worker] This is fine when condition B is not met, where hidinput_led_worker() calls hid_ll_driver->request(). This is the case for most HID drivers, which implement it or use the generic one from usbhid. The driver itself or an underlying driver will then abort processing the request. Otherwise, hidinput_led_worker() tries hid_hw_output_report() and leads to the bug. hidinput_led_worker ` hid_hw_output_report ` dispatch_hid_bpf_output_report ` srcu_read_lock(&hdev->bpf.srcu) ` srcu_read_unlock(&hdev->bpf.srcu, idx) The bug has existed since the introduction [2] of dispatch_hid_bpf_output_report(). However, the same bug also exists in dispatch_hid_bpf_raw_requests(), and I've reproduced (no visible effect because of the lack of [1], but confirmed bpf.destroyed == 1) the bug against the commit (i.e., the Fixes:) introducing the function. This is because hidinput_led_worker() falls back to hid_hw_raw_request() when hid_ll_driver->output_report() is uninplemented (e.g., logitech- djreceiver). hidinput_led_worker ` hid_hw_output_report: -ENOSYS ` hid_hw_raw_request ` dispatch_hid_bpf_raw_requests ` srcu_read_lock(&hdev->bpf.srcu) ` srcu_read_unlock(&hdev->bpf.srcu, idx) Fix the issue by returning early in the two mentioned functions if hid_bpf has been marked as destroyed. Though dispatch_hid_bpf_device_event() handles input events, and there is no evidence that it may be called after the destruction, the same check, as a safety net, is also added to it to maintain the consistency among all dispatch functions. The impact of the bug on other architectures is unclear. Even if it acts as a hidden failure, this is still dangerous because it corrupts whatever is on the address calculated by SRCU. Thus, CC'ing the stable list. [1]: commit 9d7de2aa8b41 ("x86/percpu/64: Use relative percpu offsets") [2]: commit 9286675a2aed ("HID: bpf: add HID-BPF hooks for hid_hw_output_report") | medium |
| CVE-2025-38015 | In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: fix memory leak in error handling path of idxd_alloc Memory allocated for idxd is not freed if an error occurs during idxd_alloc(). To fix it, free the allocated memory in the reverse order of allocation before exiting the function in case of an error. | medium |
| CVE-2025-38014 | In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: Refactor remove call with idxd_cleanup() helper The idxd_cleanup() helper cleans up perfmon, interrupts, internals and so on. Refactor remove call with the idxd_cleanup() helper to avoid code duplication. Note, this also fixes the missing put_device() for idxd groups, enginces and wqs. | medium |
| CVE-2025-38013 | In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: Set n_channels after allocating struct cfg80211_scan_request Make sure that n_channels is set after allocating the struct cfg80211_registered_device::int_scan_req member. Seen with syzkaller: UBSAN: array-index-out-of-bounds in net/mac80211/scan.c:1208:5 index 0 is out of range for type 'struct ieee80211_channel *[] __counted_by(n_channels)' (aka 'struct ieee80211_channel *[]') This was missed in the initial conversions because I failed to locate the allocation likely due to the "sizeof(void *)" not matching the "channels" array type. | medium |
| CVE-2025-38012 | In the Linux kernel, the following vulnerability has been resolved: sched_ext: bpf_iter_scx_dsq_new() should always initialize iterator BPF programs may call next() and destroy() on BPF iterators even after new() returns an error value (e.g. bpf_for_each() macro ignores error returns from new()). bpf_iter_scx_dsq_new() could leave the iterator in an uninitialized state after an error return causing bpf_iter_scx_dsq_next() to dereference garbage data. Make bpf_iter_scx_dsq_new() always clear $kit->dsq so that next() and destroy() become noops. | medium |
| CVE-2025-38011 | In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: csa unmap use uninterruptible lock After process exit to unmap csa and free GPU vm, if signal is accepted and then waiting to take vm lock is interrupted and return, it causes memory leaking and below warning backtrace. Change to use uninterruptible wait lock fix the issue. WARNING: CPU: 69 PID: 167800 at amd/amdgpu/amdgpu_kms.c:1525 amdgpu_driver_postclose_kms+0x294/0x2a0 [amdgpu] Call Trace: <TASK> drm_file_free.part.0+0x1da/0x230 [drm] drm_close_helper.isra.0+0x65/0x70 [drm] drm_release+0x6a/0x120 [drm] amdgpu_drm_release+0x51/0x60 [amdgpu] __fput+0x9f/0x280 ____fput+0xe/0x20 task_work_run+0x67/0xa0 do_exit+0x217/0x3c0 do_group_exit+0x3b/0xb0 get_signal+0x14a/0x8d0 arch_do_signal_or_restart+0xde/0x100 exit_to_user_mode_loop+0xc1/0x1a0 exit_to_user_mode_prepare+0xf4/0x100 syscall_exit_to_user_mode+0x17/0x40 do_syscall_64+0x69/0xc0 (cherry picked from commit 7dbbfb3c171a6f63b01165958629c9c26abf38ab) | medium |
| CVE-2025-38010 | In the Linux kernel, the following vulnerability has been resolved: phy: tegra: xusb: Use a bitmask for UTMI pad power state tracking The current implementation uses bias_pad_enable as a reference count to manage the shared bias pad for all UTMI PHYs. However, during system suspension with connected USB devices, multiple power-down requests for the UTMI pad result in a mismatch in the reference count, which in turn produces warnings such as: [ 237.762967] WARNING: CPU: 10 PID: 1618 at tegra186_utmi_pad_power_down+0x160/0x170 [ 237.763103] Call trace: [ 237.763104] tegra186_utmi_pad_power_down+0x160/0x170 [ 237.763107] tegra186_utmi_phy_power_off+0x10/0x30 [ 237.763110] phy_power_off+0x48/0x100 [ 237.763113] tegra_xusb_enter_elpg+0x204/0x500 [ 237.763119] tegra_xusb_suspend+0x48/0x140 [ 237.763122] platform_pm_suspend+0x2c/0xb0 [ 237.763125] dpm_run_callback.isra.0+0x20/0xa0 [ 237.763127] __device_suspend+0x118/0x330 [ 237.763129] dpm_suspend+0x10c/0x1f0 [ 237.763130] dpm_suspend_start+0x88/0xb0 [ 237.763132] suspend_devices_and_enter+0x120/0x500 [ 237.763135] pm_suspend+0x1ec/0x270 The root cause was traced back to the dynamic power-down changes introduced in commit a30951d31b25 ("xhci: tegra: USB2 pad power controls"), where the UTMI pad was being powered down without verifying its current state. This unbalanced behavior led to discrepancies in the reference count. To rectify this issue, this patch replaces the single reference counter with a bitmask, renamed to utmi_pad_enabled. Each bit in the mask corresponds to one of the four USB2 PHYs, allowing us to track each pad's enablement status individually. With this change: - The bias pad is powered on only when the mask is clear. - Each UTMI pad is powered on or down based on its corresponding bit in the mask, preventing redundant operations. - The overall power state of the shared bias pad is maintained correctly during suspend/resume cycles. The mutex used to prevent race conditions during UTMI pad enable/disable operations has been moved from the tegra186_utmi_bias_pad_power_on/off functions to the parent functions tegra186_utmi_pad_power_on/down. This change ensures that there are no race conditions when updating the bitmask. | low |
| CVE-2025-38009 | In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: disable napi on driver removal A warning on driver removal started occurring after commit 9dd05df8403b ("net: warn if NAPI instance wasn't shut down"). Disable tx napi before deleting it in mt76_dma_cleanup(). WARNING: CPU: 4 PID: 18828 at net/core/dev.c:7288 __netif_napi_del_locked+0xf0/0x100 CPU: 4 UID: 0 PID: 18828 Comm: modprobe Not tainted 6.15.0-rc4 #4 PREEMPT(lazy) Hardware name: ASUS System Product Name/PRIME X670E-PRO WIFI, BIOS 3035 09/05/2024 RIP: 0010:__netif_napi_del_locked+0xf0/0x100 Call Trace: <TASK> mt76_dma_cleanup+0x54/0x2f0 [mt76] mt7921_pci_remove+0xd5/0x190 [mt7921e] pci_device_remove+0x47/0xc0 device_release_driver_internal+0x19e/0x200 driver_detach+0x48/0x90 bus_remove_driver+0x6d/0xf0 pci_unregister_driver+0x2e/0xb0 __do_sys_delete_module.isra.0+0x197/0x2e0 do_syscall_64+0x7b/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e Tested with mt7921e but the same pattern can be actually applied to other mt76 drivers calling mt76_dma_cleanup() during removal. Tx napi is enabled in their *_dma_init() functions and only toggled off and on again inside their suspend/resume/reset paths. So it should be okay to disable tx napi in such a generic way. Found by Linux Verification Center (linuxtesting.org). | low |
| CVE-2025-38008 | In the Linux kernel, the following vulnerability has been resolved: mm/page_alloc: fix race condition in unaccepted memory handling The page allocator tracks the number of zones that have unaccepted memory using static_branch_enc/dec() and uses that static branch in hot paths to determine if it needs to deal with unaccepted memory. Borislav and Thomas pointed out that the tracking is racy: operations on static_branch are not serialized against adding/removing unaccepted pages to/from the zone. Sanity checks inside static_branch machinery detects it: WARNING: CPU: 0 PID: 10 at kernel/jump_label.c:276 __static_key_slow_dec_cpuslocked+0x8e/0xa0 The comment around the WARN() explains the problem: /* * Warn about the '-1' case though; since that means a * decrement is concurrent with a first (0->1) increment. IOW * people are trying to disable something that wasn't yet fully * enabled. This suggests an ordering problem on the user side. */ The effect of this static_branch optimization is only visible on microbenchmark. Instead of adding more complexity around it, remove it altogether. | medium |
| CVE-2025-38007 | In the Linux kernel, the following vulnerability has been resolved: HID: uclogic: Add NULL check in uclogic_input_configured() devm_kasprintf() returns NULL when memory allocation fails. Currently, uclogic_input_configured() does not check for this case, which results in a NULL pointer dereference. Add NULL check after devm_kasprintf() to prevent this issue. | medium |
| CVE-2025-38006 | In the Linux kernel, the following vulnerability has been resolved: net: mctp: Don't access ifa_index when missing In mctp_dump_addrinfo, ifa_index can be used to filter interfaces, but only when the struct ifaddrmsg is provided. Otherwise it will be comparing to uninitialised memory - reproducible in the syzkaller case from dhcpd, or busybox "ip addr show". The kernel MCTP implementation has always filtered by ifa_index, so existing userspace programs expecting to dump MCTP addresses must already be passing a valid ifa_index value (either 0 or a real index). BUG: KMSAN: uninit-value in mctp_dump_addrinfo+0x208/0xac0 net/mctp/device.c:128 mctp_dump_addrinfo+0x208/0xac0 net/mctp/device.c:128 rtnl_dump_all+0x3ec/0x5b0 net/core/rtnetlink.c:4380 rtnl_dumpit+0xd5/0x2f0 net/core/rtnetlink.c:6824 netlink_dump+0x97b/0x1690 net/netlink/af_netlink.c:2309 | high |
| CVE-2025-38005 | In the Linux kernel, the following vulnerability has been resolved: dmaengine: ti: k3-udma: Add missing locking Recent kernels complain about a missing lock in k3-udma.c when the lock validator is enabled: [ 4.128073] WARNING: CPU: 0 PID: 746 at drivers/dma/ti/../virt-dma.h:169 udma_start.isra.0+0x34/0x238 [ 4.137352] CPU: 0 UID: 0 PID: 746 Comm: kworker/0:3 Not tainted 6.12.9-arm64 #28 [ 4.144867] Hardware name: pp-v12 (DT) [ 4.148648] Workqueue: events udma_check_tx_completion [ 4.153841] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 4.160834] pc : udma_start.isra.0+0x34/0x238 [ 4.165227] lr : udma_start.isra.0+0x30/0x238 [ 4.169618] sp : ffffffc083cabcf0 [ 4.172963] x29: ffffffc083cabcf0 x28: 0000000000000000 x27: ffffff800001b005 [ 4.180167] x26: ffffffc0812f0000 x25: 0000000000000000 x24: 0000000000000000 [ 4.187370] x23: 0000000000000001 x22: 00000000e21eabe9 x21: ffffff8000fa0670 [ 4.194571] x20: ffffff8001b6bf00 x19: ffffff8000fa0430 x18: ffffffc083b95030 [ 4.201773] x17: 0000000000000000 x16: 00000000f0000000 x15: 0000000000000048 [ 4.208976] x14: 0000000000000048 x13: 0000000000000000 x12: 0000000000000001 [ 4.216179] x11: ffffffc08151a240 x10: 0000000000003ea1 x9 : ffffffc08046ab68 [ 4.223381] x8 : ffffffc083cabac0 x7 : ffffffc081df3718 x6 : 0000000000029fc8 [ 4.230583] x5 : ffffffc0817ee6d8 x4 : 0000000000000bc0 x3 : 0000000000000000 [ 4.237784] x2 : 0000000000000000 x1 : 00000000001fffff x0 : 0000000000000000 [ 4.244986] Call trace: [ 4.247463] udma_start.isra.0+0x34/0x238 [ 4.251509] udma_check_tx_completion+0xd0/0xdc [ 4.256076] process_one_work+0x244/0x3fc [ 4.260129] process_scheduled_works+0x6c/0x74 [ 4.264610] worker_thread+0x150/0x1dc [ 4.268398] kthread+0xd8/0xe8 [ 4.271492] ret_from_fork+0x10/0x20 [ 4.275107] irq event stamp: 220 [ 4.278363] hardirqs last enabled at (219): [<ffffffc080a27c7c>] _raw_spin_unlock_irq+0x38/0x50 [ 4.287183] hardirqs last disabled at (220): [<ffffffc080a1c154>] el1_dbg+0x24/0x50 [ 4.294879] softirqs last enabled at (182): [<ffffffc080037e68>] handle_softirqs+0x1c0/0x3cc [ 4.303437] softirqs last disabled at (177): [<ffffffc080010170>] __do_softirq+0x1c/0x28 [ 4.311559] ---[ end trace 0000000000000000 ]--- This commit adds the missing locking. | medium |
| CVE-2025-37976 | Rejected reason: This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. | No Score |
| CVE-2025-3739 | Vulnerability in Drupal Drupal 8 Google Optimize Hide Page.This issue affects Drupal 8 Google Optimize Hide Page: *.*. | medium |
| CVE-2025-3522 | Thunderbird processes the X-Mozilla-External-Attachment-URL header to handle attachments which can be hosted externally. When an email is opened, Thunderbird accesses the specified URL to determine file size, and navigates to it when the user clicks the attachment. Because the URL is not validated or sanitized, it can reference internal resources like chrome:// or SMB share file:// links, potentially leading to hashed Windows credential leakage and opening the door to more serious security issues. This vulnerability affects Thunderbird < 137.0.2 and Thunderbird < 128.9.2. | medium |
| CVE-2025-3509 | A Remote Code Execution (RCE) vulnerability was identified in GitHub Enterprise Server that allowed attackers to execute arbitrary code by exploiting the pre-receive hook functionality, potentially leading to privilege escalation and system compromise. The vulnerability involves using dynamically allocated ports that become temporarily available, such as during a hot patch upgrade. This means the vulnerability is only exploitable during specific operational conditions, which limits the attack window. Exploitation required either site administrator permissions to enable and configure pre-receive hooks or a user with permissions to modify repositories containing pre-receive hooks where this functionality was already enabled. This vulnerability affected all versions of GitHub Enterprise Server prior to 3.18 and was fixed in versions 3.17.1, 3.16.4, 3.15.8, 3.14.13, 3.13.16. This vulnerability was reported via the GitHub Bug Bounty program. | high |
| CVE-2025-32789 | EspoCRM is an Open Source Customer Relationship Management software. Prior to version 9.0.7, users can be sorted by their password hash. This flaw allows an attacker to make assumptions about the hash values of other users stored in the password column of the user table, based on the results of the sorted list of users. Although unlikely, if an attacker knows the hash value of their password, they can change the password and repeat the sorting until the other user's password hash is fully revealed. This issue is patched in version 9.0.7. | low |
| CVE-2025-32412 | Fuji Electric Smart Editor is vulnerable to an out-of-bounds read, which may allow an attacker to execute arbitrary code. | high |
| CVE-2025-32106 | In Audiocodes Mediapack MP-11x through 6.60A.369.002, a crafted POST request request may result in an unauthenticated remote user's ability to execute unauthorized code. | critical |
| CVE-2025-32105 | A buffer overflow in the the Sangoma IMG2020 HTTP server through 2.3.9.6 allows an unauthenticated user to achieve remote code execution. | critical |
| CVE-2025-32028 | HAX CMS PHP allows you to manage your microsite universe with PHP backend. Multiple file upload functions within the HAX CMS PHP application call a ’save’ function in ’HAXCMSFile.php’. This save function uses a denylist to block specific file types from being uploaded to the server. This list is non-exhaustive and only blocks ’.php’, ’.sh’, ’.js’, and ’.css’ files. The existing logic causes the system to "fail open" rather than "fail closed." This vulnerability is fixed in 10.0.3. | critical |
| CVE-2025-30642 | A link following vulnerability in Trend Micro Deep Security 20.0 agents could allow a local attacker to create a denial of service (DoS) situation on affected installations. Please note: an attacker must first obtain the ability to execute low-privileged code on the target system in order to exploit this vulnerability. | medium |
| CVE-2025-30641 | A link following vulnerability in the anti-malware solution portion of Trend Micro Deep Security 20.0 agents could allow a local attacker to escalate privileges on affected installations. Please note: an attacker must first obtain the ability to execute low-privileged code on the target system in order to exploit this vulnerability. | high |
| CVE-2025-30640 | A link following vulnerability in Trend Micro Deep Security 20.0 agents could allow a local attacker to escalate privileges on affected installations. Please note: an attacker must first obtain the ability to execute low-privileged code on the target system in order to exploit this vulnerability. | high |
| CVE-2025-30080 | Signalling in Pexip Infinity 29 through 36.2 before 37.0 has improper input validation that allows remote attackers to trigger a temporary denial of service (software abort). | high |
| CVE-2025-29885 | An improper certificate validation vulnerability has been reported to affect File Station 5. If exploited, the vulnerability could allow remote attackers who have gained user access to compromise the security of the system. We have already fixed the vulnerability in the following versions: File Station 5 5.5.6.4791 and later and later | high |
| CVE-2025-29884 | An improper certificate validation vulnerability has been reported to affect File Station 5. If exploited, the vulnerability could allow remote attackers who have gained user access to compromise the security of the system. We have already fixed the vulnerability in the following versions: File Station 5 5.5.6.4791 and later and later | high |
