Detections
Analytics

17.9.1 Ensure 'Audit IPsec Driver' is set to 'Success and Failure'

Warning! Audit Deprecated

This audit has been deprecated and will be removed in a future update.

View Next Audit Version

Information

This subcategory reports on the activities of the Internet Protocol security (IPsec) driver. Events for this subcategory include:

4960: IPsec dropped an inbound packet that failed an integrity check. If this problem persists, it could indicate a network issue or that packets are being modified in transit to this computer. Verify that the packets sent from the remote computer are the same as those received by this computer. This error might also indicate interoperability problems with other IPsec implementations.

4961: IPsec dropped an inbound packet that failed a replay check. If this problem persists, it could indicate a replay attack against this computer.

4962: IPsec dropped an inbound packet that failed a replay check. The inbound packet had too low a sequence number to ensure it was not a replay.

4963: IPsec dropped an inbound clear text packet that should have been secured. This is usually due to the remote computer changing its IPsec policy without informing this computer. This could also be a spoofing attack attempt.

4965: IPsec received a packet from a remote computer with an incorrect Security Parameter Index (SPI). This is usually caused by malfunctioning hardware that is corrupting packets. If these errors persist, verify that the packets sent from the remote computer are the same as those received by this computer. This error may also indicate interoperability problems with other IPsec implementations. In that case, if connectivity is not impeded, then these events can be ignored.

5478: IPsec Services has started successfully.

5479: IPsec Services has been shut down successfully. The shutdown of IPsec Services can put the computer at greater risk of network attack or expose the computer to potential security risks.

5480: IPsec Services failed to get the complete list of network interfaces on the computer. This poses a potential security risk because some of the network interfaces may not get the protection provided by the applied IPsec filters. Use the IP Security Monitor snap-in to diagnose the problem.

5483: IPsec Services failed to initialize RPC server. IPsec Services could not be started.

5484: IPsec Services has experienced a critical failure and has been shut down. The shutdown of IPsec Services can put the computer at greater risk of network attack or expose the computer to potential security risks.

5485: IPsec Services failed to process some IPsec filters on a plug-and-play event for network interfaces. This poses a potential security risk because some of the network interfaces may not get the protection provided by the applied IPsec filters. Use the IP Security Monitor snap-in to diagnose the problem.

The recommended state for this setting is: Success and Failure.

Rationale:

Auditing these events may be useful when investigating a security incident.

Impact:

If no audit settings are configured, or if audit settings are too lax on the computers in your organization, security incidents might not be detected or not enough evidence will be available for network forensic analysis after security incidents occur. However, if audit settings are too severe, critically important entries in the Security log may be obscured by all of the meaningless entries and computer performance and the available amount of data storage may be seriously affected. Companies that operate in certain regulated industries may have legal obligations to log certain events or activities.

Solution

To establish the recommended configuration, set the following Device Configuration Policy to Success and Failure:

To access the Device Configuration Policy from the Intune Home page:

Click Devices

Click Configuration profiles

Click Create profile

Select the platform (Windows 10 and later)

Select the profile (Custom)

Enter a Name

Click Add

Enter the Details below

Name: <Enter name>
Description: <Enter Description>
OMA-URI: ./Device/Vendor/MSFT/Policy/Config/Audit/System_AuditIPsecDriver
Data type: Integer
Value: 3

Select Save

Continue through the Wizard to complete the creation of the profile (profile assignments, applicability etc.)

OR

To access the Device Configuration Policy from the Intune Home page:

Click Devices

Click Configuration profiles

Click Create profile

Select the platform (Windows 10 and later)

Select the profile (Settings Picker)

Click Create

Enter a Name

Click Add settings

Configure the following Setting:

Path: Auditing
Setting Name: System Audit I Psec Driver
Configuration: Success+ Failure

Continue through the Wizard to complete the creation of the profile (profile assignments, applicability etc.)

Note: More than one configuration setting from each of the Configuration profiles (ex: Administrative Templates, Custom etc.) can be added to each Device Configuration Policy.

Default Value:

No Auditing.

See Also

https://workbench.cisecurity.org/benchmarks/14355

Item Details

References: CSCv7|6.3

Plugin: Windows

Control ID: 09d151755b431073bffb70989bacf63c7a67ed0a8c5c01649ec143c6a80d80be